Introduction


One of the main focuses of the recent advances in Spine surgery has been on motion preservation of a degenerative functional spinal unit.

Anterior discectomy and fusion is still the gold standard procedure for symptomatic cervical disc disease. However, long-term results following fusion showed evidence of adjacent segment disease, especially in young and active population1. This has led to the development of cervical disc replacement with the aim of reducing adjacent spondylitic change.

Cummins attempted to address the shortcoming of cervical arthrodesis 15 years ago2. His pioneering efforts in the development of a metal-on-metal cervical artificial disc laid the foundation on which the Prestige (Medtronic Sofamor Danek, Inc., Memphis, TN) was designed.

Indications and goals of total cervical disc replacement
The indications for cervical total disc replacement are principally the same as for ACDF (anterior cervical decompression and fusion) with a few exceptions. A symptomatic disc, which lead to arm and/or neck pain and/or radiculopathy with sensory-motor deficits. These symptoms may be caused by a herniated disc and/or osteophytes compressing adjacent exiting nerves roots or the spinal cord. The goals are to restore the intervertebral disc height and neuroforaminal height to prevent recurrence of neurologic compression.

There is general consensus, that the ability of an artificial disc to correct deformities and to restore physiological lordosis is limited.

A total disc replacement is contraindicated in all types of anterolisthesis and in patients who have had a laminectomy.

The use of arthroplasty in the myelopathic patient, as opposed to fusion surgery, is a controversial area. While a reasonable option for patients with normal sagittal balance, minimal degenerative disease, and one- or two-level disc disease causing root compression, there are many situations where fusion is a better choice than arthroplasty in most situations.

Some of the Currently Available Cervical Disc Prostheses

Prestige (Medtronic Sofamor Danek, Memphis, USA)
The second generation of the Cummins/Bristol cervical disc was Prestige I cervical prosthesis (also named Frenchay artificial joint), developed in 1998. It is a two-piece prosthesis constructed of stainless steel and employs a ball-in-groove articulation (Medtronic Sofamor Danek;). This semi-constrained arrangement allows a greater degree of translation to occur with rotation. It is a modified version of the original Cummins prosthesis which was based on a ball-and-socket design.

The Prestige II was designed in 1999 and main difference to its predecessor being a more anatomic end-plate design; porous coated to improve bony ingrowth3. In a prospective, randomised clinical trial, Porchet et al4 compared the Prestige II Cervical Disc with ACDF for the treatment of single-level disease and their radiographic results showed that Prestige II disc maintains motion at the treated level without adjacent-segment compromise.

The Prestige ST became available in 2002 and the major change from Prestige II was a 2-mm reduction in the height of each anterior flange. Mummaneni PV et al5 in a randomised controlled trial compared ACDF in patients treated for symptomatic single-level cervical degenerative disc disease with PRESTIGE ST Cervical Disc System. The PRESTIGE ST Cervical Disc System maintained physiological segmental motion at 24 months after implantation and was associated with improved neurological success, improved clinical outcomes, and a reduced rate of secondary surgeries compared with ACDF.

The Prestige LP is manufactured from a unique titanium ceramic composite material that is highly durable and image-friendly on computed tomographic and magnetic resonance imaging scans. The ball-and-trough articulation is identical to that of the Prestige ST. Initial fixation is achieved via four rails, two on each component, which engage the vertebral bodies. The plasma-spray titanium coating encourages subsequent bony integration.

The Food and Drug Administration (FDA) cleared the Prestige ST Cervical Disc System in July 2007.

ProDisc-C (Synthes Spine, Paoli, PA, USA)
The ProDisc-C cervical disc replacement (Synthes) is constructed of two cobalt-chromium-molybdenum endplates with a metal-on-polyethylene bearing surface and a fixed polyethylene core. The surfaces of the prosthesis towards the bones bear a plasma-spray titanium layer for secondary fixation by bone ingrowth. A central keel that inserts in a slot with in the cranial and caudal vertebral bodies.

Bryan Disc (Medtronic Sofamor Danek, Memphis, USA)
The Bryan cervical disc consists of a polycarbonate, polyurethane core situated between two convex porous coated titanium shells and encapsulated around the periphery by a polymer sheath. This design allows for a range of motion in flexion/extension, lateral bending, rotation and translation as well as coupled motions similar to the normal cervical spine functional unit.

In 2002 Goffin et al. reported one year follow-up on the results of 60 patients treated with the Bryan® intervertebral cervical disk prosthesis. Ninety per cent of patients reported functional success with n